Firmware Selector

Firmware Selector

Version information below

---

Select a Release:

Latest Release Loading...

Select a Release:

Older Releases may not be fully compatible with the Selector

Select a month to load releases

Selected Release Tag:

latest

Model:

--Optional-- Aquila Aquila X3/S3 HC32 Ender-3V2/S1

ProUI Extra Features:

Yes No

LCD Display:

--Select-- DWIN TJC 12864

Board Type:

--Select-- GD32 N32 HC32 Creality 4.2.7 Creality 4.2.2 Creality E3 Free-runs Ender-3 S1 F103 Ender-3 S1 F401 BTT SKR Mini E3

Features:

--Select-- CR/3D/BL-Touch BIQU MicroProbe V2 Induction Probe Creality Sprite

Secondary Features:

--Select-- BIQU MicroProbe V2 Induction Probe Creality Sprite

Leveling:

--Select-- Unified Bed Leveling Bilinear Bed Leveling Manual Mesh Default

Options:

--Select-- MPC Input Shaping Power-loss Recovery

Secondary Options:

--Select-- MPC Input Shaping Power-loss Recovery

---

📚 Versions

---

Some versions do have options like Power-loss Recovery despite not having it in the file name.
Board types 422/427, and leveling options Default/Manual Mesh should have this and other options enabled which may not be available in base UBL/BLT ProUI-EX versions.

These are the configurations offered:

Bed Leveling Options

• [ _Default-NP ]: Use if you have a near stock machine^{Default No Probe}
• [ _MM ]: Create a bed mesh without an auto bed probe^{Manual Mesh Bed Leveling}
• [ _BLT ]: Use if you have a CR/3D/BL-Touch level sensor installed.^{Bilinear Auto Bed Leveling}
• [ _UBL ]: Similar to both MM and BLT - with more options. Recommended over BLT^{Unified Bed Leveling}

Special Versions

^{(List of file prefixes and suffixes)}

• [ -ProUI-EX ]
  | ProUI Extra Features |

  Toolbar, change bed physical dimensions, and other special features and options

• [ _E3-Free-runs ]
  | Creality E3 Free-runs | (Creality board - TMC2209 drivers)
• [ -S1-<F1/F4&gt ]
  | Creality Ender-3 S1 | (Check to see whether you have F1 or F4)
  -S1-F1: STM32F103RC chip and CREALITY_V24S1_301 board
  -S1-F4: STM32F401RC chip and CREALITY_V24S1_301F4 board

  LCD Displays

  [ DWIN ]
  | Stock DWIN LCD | (No actual prefix)

  [ TJC- ]
  | Creality TJC LCD | (As aftermarket or sometimes used in stock Creality machines)

  [ C2- ]
  | Monochrome 128x64 LCD | (Used in Aquila C2 and original Ender-3/CR-10) ^{This has NO ProUI capabilities}

  Features

  [ _SPRT13 ]
  | Sprite Extruder | (Uses thermistor # 13)

  [ _IND ]
  | Inductive Sensor | (Probe used on X3/S3 models)
  CAUTION: You may need to adjust the Probe Y Offset to -20 or -25 on an S3

  [ _BMP ]
  | BIQU MicroProbe V2.0 | (Alternative to CR/3D/BL/-Touch) ^{Use ONLY this firmware with _BMP if you DO have this probe}

  Options

  [ -IS ]
  | Input Shaping | (Similar to Linear Advance) ^{Use ONLY if you mean to do the initial calibration✶}

  [ -MPC ]
  | MPC Autotune | (Replaces PID for hotend)

  [ -PLR ]
  | Power-Loss Recovery | (Resumes where a print job left off when there is a power outage)

^{✶Reminder: Do not use `Input Shaping` (file suffix -IS) unless you do the necessary calibration.
Prints will be effected regardless. May require a special breakout board or test prints to calibrate.}